How to fix iPhone X Voltage Jumping

iPhone X Screen jumps and skips when i touch it sometimes

After getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply, and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter, there is no short circuit was found for the dipole value of all power supply to ground.

We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check the CPU power supply! As shown in iPhone schemtic diagram 14-3-1 and 14-3-2, there are three ways of power supply, not only directly into the CPU, but also through the small resistance or inductance into the CPU, the three voltage are PP1V2_SOC, PP0V8_SOC_FIXED_S1, PP1V8_IO.

14-3-1

14-3-2

Testing the 3 power supply one by one, when the FL1092 inductor of PP1V8_IO is measured, one end is 1.8V while the other end is 0V.

14-3-3

Testing the end without voltage to the ground dipole value is 490, the normal is about 280. Then testing the inductor's noumenon value is very large, indicating the iPhone X inductor is damaged, so we replace a new inductor, the fault is repaired well.

Later, it was analyzed that the PP1V8_IO was renamed as PP1V8_XTAL after inductance FL1092, which was supplied to the CPU crystal module. It also verified that the voltage jump of iPhone X and the voltage jump of 7P before were actually the same thing.

Hope this iPhone X repair case will help you.

Comments

Post a Comment

Popular posts from this blog

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac
Read more

Setup and install the zxw tool Dongle Wizard

Image
So, you recently purchased ZXW Tools from our vipprog online store have no clue how to set it up?  Well, here is a quick guide detailing the installation process. Step 1 Unbox the ZXW tools dongle and plug it into your Windows PC.  ZXW tools does not support Mac at this time, so you’ll need a Windows compatible box. Step 2 Download the ZXW Tools software [direct link].  The ZXW tools website is in Chinese, but lucky for you, we’ve made it easy for you to download the latest version of their software directly from our website.  The zip file contains all of the files necessary to run ZXW Tools (trace) and Blackfish (schematics).  There is no installation process.  You just need to copy the files over to a directory on your desktop. Step 3 After you’ve copied all of the files over to a folder on  your desktop, then just run the ZXW tools executable.as shown in the picture. When your first run the software, the program will ask you if you want to activate the dong
Read more

IPhone 6P Front Camera and Distance Sensor Fault

Image
Received a iPhone 6 Plus, the customer said that the front camera can not be used, and the distance sensor has problem too. The two failures are concentrated on the front camera flex cable, which is likely to be caused by the damage of the wiring. First, we have to eliminate the possibility of the external parts fault, then consider the motherboard problem. Remove the screen assembly and replace it with a good one, we still can't turn on the front camera and use the distance sensor. Disassemble to measure the ground resistance of the front camera seat of J1111 by Fluke digital multimeter , it is found that several pins are infinitely large, and the related inductors are loose when touch with the pen. It seems that the small components are pseudo welded. 19-1- 1 Remove the motherboard and observe it under the Trinocular Stereo Microscope , we can see that the touch was repaired before. 19-1-2 The back of the sub touch chip U2402 is the front camera seat J1111, an
Read more