Professional iPhone mobile phone repair tools and programmer tool

IP BOX V2 iP high speed programmer IPBOX 2 for iPhone / iPad, from vipprogrammer.com

New IP BOX V2 is the iP High Speed Programmer for iPhone / iPad device, Support Apple NAND Flash, Baseband EEPROM, CHIP Read Write Erase Repair function, help engineer fix the brush and boot errors on hardwares.

IP BOX V2 / IPBOX 2 iP high speed programmer for iPhone / iPad (All-in-One machine)

This machine case Apple NAND Model,  not Match the iphone / ipad model.  perhpas, parts NAND mode can't supported,  the factory will added in future,
others Tools,  Model: VP406 / W002 / VP405 / VC199/ W004/ W005 / W012... just case iphone / ipad Model, don't match Apple NAND.

Don't need Boot Nand Flash, easy to use, also don't need Apple engineering Cables (DCSD USB cable )

Features:

1: APPLE NAND Flash supported list
64bit:  iphone 5s, 6,6p; ipad mini2/3, ipad5/6 underlying data modification, SN, country, color, wifi...modification
32bit:  iphone 5, 5c, 4s, 4;  ipad 2/3/4,mini1 underlying data modification, SN, country, color, wifi...modification
2. Apple EEPROM IC (IMEI CHIP) supported list
PCIE Mode:  support iphone 5se, 6s, 6sp EEPROM IC reading / writing, underlying data repairing
64bit Mode: support 5s, 5se, 6, 6p EEPROM IC reading / writing, underlying data repairing
32bit Mode:  support 5, 5c, 4s, 4, EEPROM IC reading / writing, underlying data repairing
3: support iphone 5s underlying data change. and when change the NAND Flash on iphone 5S, fingerprints function is also working well.

Comments

Post a Comment

Popular posts from this blog

How to fix iPhone 6 show Power current 70mA can’t turned on

Image
Your iPhone will not turn on and you’re looking for help. It’s a problem that can be easy or difficult to fix, depending on the cause.In this article,A customer's IPhone6 after triggering it on, the turn on current is 70mA. This customer used iTunes to root it, but the root did not pass and iTunes reported error 4014. Repair Process Customer himself used air gun  to heat CPU. When connect computer to root, computer reports error 4014. In general, error 4014 suggests that CPU, Temporary Storage is more or less faulty or the power supply circuits are faulty. After removing the motherboard , we find that around the shield cover of motor drive chip U1400 there is some erosion mark, as shown in picture 5-41. Picture 5-41 Removing the shield cover , we can see that U1400 is eroded. Picture 5-42 shows erosion situation of the enlarged motor drive chip U1400. Picture 5-42 Clean the eroded places and replace U1400. Now iPhone can be turned on normally. The motor drive chip ...
Read more

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac...
Read more

What to do if iPhone 6s can't add fingerprint

Image
My iPhone's Touch ID fingerprint scanner's not working! It won't recognise the fingerprints stored in the system. How can I fix Touch ID? The iPhone 6S accidentally dropped into the water, and then it came up with a fingerprint faulty, the iPhone 6S can't add fingerprint. So the customer sent it to us to repair. Now, let's take a closer look at this iPhone and then repair it! Disassemble the iPhone by JM-P01 Toolkit  , carefully remove the iPhone motherboard. After checking, we found signs of corrosion in the fingerprint socket, and then detect MESA_TO_BOOST_EN_CONN. Use Fluke 15B+ Digital Multimeter  to measure the diode data of PP16V5_MESA_CONN fingerprint boost boot signal and 16.5V, the data is normal. Observe the iPhone PCB board carefully under the VGA Camera 7-45X Trinocular Stereo Microscope  , we found something else. The bottom pin was severely corroded after the corrosion was removed from the fingerprint boost U4040. A2 pin PP_VCC_MAIN is disconn...
Read more