Repair iPhone 6 won't turn on issue

Yesterday, a friend sent us an iPhone 6 need to be repaired, the iPhone 6 directly short-circuit after connected it to DC power supply, large current short circuit and iPhone motherboard is overheating. We think it's small problem, disassemble the iPhone, and we found the iPhone charge tube is hot. Remove the shield cover and apply some rosin, obviously the iPhone baseband power is damaged. Remove the iPhone baseband power and then connect iPhone logic to DC power supply, the iPhone boot, but no display, check it more clearly, several pins on the socket are damaged.

Picture 19-7-1

Remove the socket, clean up the solder pad, and then re-solder the good socket to it. After replacement, the iPhone can be turned on normally, but there is no baseband.

Install the new iPhone baseband power, but there's no SIM card malfunction, continue to measure it, also no front and rear camera. The iPhone 6 no front and rear camera is usually caused by 2.85V power supply problem, directly find a regulated conversion tube. Scrape off the glue, and then solder a jumper wire. We can check the bitmap in the WUXINJI Dongle.

Picture 19-7-2

Based the picture, soldering a jumper wire from photosensitive 3V to camera 2.85V, and then test the iPhone camera, the rear camera is normal, but the front camera not. The data measured by Fluke 15B+ Digital Multimeter all is normal. We think the iPhone has been flashed when the camera is damaged. Because there is an ID, so we can't flash the iPhone, and the customer doesn't care this failure, so directly install the iPhone.

After install the iPhone, turn on iPhone, after Apple logo appears 2 seconds, it's automatically turned off. Connect iPhone to the DC power supply, the current jumps from 80 to 160, after a while, it turns 0. According to our experience, we think it's iPhone Nand flash problem.

Picture 19-7-3

From the above picture, we can see that this shield cover has been dented by a lot of external damage，it seems the iPhone Nand flash virtual weld. Directly remove the iPhone Nand flash, re-weld it and then install it, but the problem still there.

19-7-4

Now, we need to flash the iPhone, get the ID from customer to flash the iPhone by iTunes. After flashing the iPhone, the problem was solved, it's a system problem.

Comments

Post a Comment

Popular posts from this blog

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac
Read more

Setup and install the zxw tool Dongle Wizard

Image
So, you recently purchased ZXW Tools from our vipprog online store have no clue how to set it up?  Well, here is a quick guide detailing the installation process. Step 1 Unbox the ZXW tools dongle and plug it into your Windows PC.  ZXW tools does not support Mac at this time, so you’ll need a Windows compatible box. Step 2 Download the ZXW Tools software [direct link].  The ZXW tools website is in Chinese, but lucky for you, we’ve made it easy for you to download the latest version of their software directly from our website.  The zip file contains all of the files necessary to run ZXW Tools (trace) and Blackfish (schematics).  There is no installation process.  You just need to copy the files over to a directory on your desktop. Step 3 After you’ve copied all of the files over to a folder on  your desktop, then just run the ZXW tools executable.as shown in the picture. When your first run the software, the program will ask you if you want to activate the dong
Read more

IPhone 6P Front Camera and Distance Sensor Fault

Image
Received a iPhone 6 Plus, the customer said that the front camera can not be used, and the distance sensor has problem too. The two failures are concentrated on the front camera flex cable, which is likely to be caused by the damage of the wiring. First, we have to eliminate the possibility of the external parts fault, then consider the motherboard problem. Remove the screen assembly and replace it with a good one, we still can't turn on the front camera and use the distance sensor. Disassemble to measure the ground resistance of the front camera seat of J1111 by Fluke digital multimeter , it is found that several pins are infinitely large, and the related inductors are loose when touch with the pen. It seems that the small components are pseudo welded. 19-1- 1 Remove the motherboard and observe it under the Trinocular Stereo Microscope , we can see that the touch was repaired before. 19-1-2 The back of the sub touch chip U2402 is the front camera seat J1111, an
Read more