iPhone 6 WIFI is not available,how to fix?

When your iPhone 6 WiFi dropping out or not available is very frustrating, don't worry, check out our more extensive WiFi Guide for additional tips. And if something worked for you that's not listed, let us know. We love sharing information and learning new approaches to help you.

The customer send an iPhone 6 without WIFI, the customer said: "two mobile phone repair shop tried to fix it but didn't succeed". There are lots of solder flux cover on WiFi, it seems that WiFi has been replaced several times, a nearby resistor is also lost , the bottom of WIFI is scraped to copper wire, we can certainly confirm it's not the iPhone 6 WIFI module problem.

First remove the WIFI and boot device to measure the voltage of WIFI bottom board pin, we find that 14 pin has no signal voltage, it should be 1.8V. The problem comes from here. Using a digital multimeter to measure but no resistance, so we use WUXINJI bitmap to check and find it is directly through CPU, is it the bottom board wire disconnection?

It can be seen from the bitmap 10-25-1 that the iPhone 6 bottom board wire is really disconnected.

Now we have to see if there is another way, continue to look at the principle diagram Apple 6. As shown in picture 10-25-2 and 10-25-3.

This reset signal has a capacitor and a pull-up resistor. The capacitance is next to WIFI. There is no resistance in the measurement. This is hopeless, then we look at the pull-up resistor again, find it is on the back of the iPhone 6 CPU from the bitmap, and it's very close. Measuring resistance is 446, then directly solder jumper wire, install WIFI, but the icon is still gray. Then we think the WIFI may be broken. Immediately replace a new WIFI chip, Bluetooth is shown up, WIFI also appeared, the fault is fixed now! Picture 10-25-4




Comments

Post a Comment

Popular posts from this blog

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac...
Read more

Setup and install the zxw tool Dongle Wizard

Image
So, you recently purchased ZXW Tools from our vipprog online store have no clue how to set it up?  Well, here is a quick guide detailing the installation process. Step 1 Unbox the ZXW tools dongle and plug it into your Windows PC.  ZXW tools does not support Mac at this time, so you’ll need a Windows compatible box. Step 2 Download the ZXW Tools software [direct link].  The ZXW tools website is in Chinese, but lucky for you, we’ve made it easy for you to download the latest version of their software directly from our website.  The zip file contains all of the files necessary to run ZXW Tools (trace) and Blackfish (schematics).  There is no installation process.  You just need to copy the files over to a directory on your desktop. Step 3 After you’ve copied all of the files over to a folder on  your desktop, then just run the ZXW tools executable.as shown in the picture. When your first run the software, the program will ask yo...
Read more

IPhone 6P Front Camera and Distance Sensor Fault

Image
Received a iPhone 6 Plus, the customer said that the front camera can not be used, and the distance sensor has problem too. The two failures are concentrated on the front camera flex cable, which is likely to be caused by the damage of the wiring. First, we have to eliminate the possibility of the external parts fault, then consider the motherboard problem. Remove the screen assembly and replace it with a good one, we still can't turn on the front camera and use the distance sensor. Disassemble to measure the ground resistance of the front camera seat of J1111 by Fluke digital multimeter , it is found that several pins are infinitely large, and the related inductors are loose when touch with the pen. It seems that the small components are pseudo welded. 19-1- 1 Remove the motherboard and observe it under the Trinocular Stereo Microscope , we can see that the touch was repaired before. 19-1-2 The back of the sub touch chip U2402 is the front camera seat J1111, an...
Read more