The free repair manual iphone 6 power-on Leakage 200mA

Phone leakage is occasionally also happen, it is very bad, don't worry, Vipprog tell you how to solve.

Generally, if cell phone device is tested as 200mA electric leakage when booting, the first choice is to replace USB tube. Of course, this is not absolute, the iPhone 6 we are going to fix today is not caused by the USB tube fault.

Connecting the iPhone 6 with multimeter, the current shows 200mA. we directly replace a USB tube. The result is that the current is still in the 200mA position after waiting for a few minutes.

So we wonder if there is another fault symptom happened, the last repair technician mentioned the iPhone 6 fingerprint is not good.

When heard of this problem, we can basically judge where the problem is. Connecting multimeter and trigger the on-off current with 300-400 mA, this is not normal. There must be something wrong with the fingerprint 3V. Use the multimeter to test fingerprint 3V against the ground value, it is short. This kind of situation is generally caused by one of outside capacitance is short, dismantling it! Finally, we find out the C2133 is short circuit, pry it off with phone IC repair knfe , reboot the iPhone 6 and retest the standby value is normal, and the fingerprint is also normal now.

The iPhone 6 schematic diagram IC postion is shown in picture 11-8-1.

Summary of leakage detection process:

We must test the function of system as possible we can in advance if we encounter the leakage, which will be repaired if any of the functions are tested abnormal, if all is normal, USB tube will be required to pay more attention. USB tube is also a problem, if it gets bad, the function will be normal and no problem can not be detected. If there is a electric leakage on the iPhone, you can first press the iPhone power button and loose to see how much the current will be. In the normal case, it is about one hundred. If it jumps to three hundred or four hundred, there must be electric leakage, and jump to two hundred or three hundred leakage is basically caused by several 3V: The 3v power supply of USB tube, the 3V of fingerprint and the 3V of compass.

Comments

Post a Comment

Popular posts from this blog

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac
Read more

Setup and install the zxw tool Dongle Wizard

Image
So, you recently purchased ZXW Tools from our vipprog online store have no clue how to set it up?  Well, here is a quick guide detailing the installation process. Step 1 Unbox the ZXW tools dongle and plug it into your Windows PC.  ZXW tools does not support Mac at this time, so you’ll need a Windows compatible box. Step 2 Download the ZXW Tools software [direct link].  The ZXW tools website is in Chinese, but lucky for you, we’ve made it easy for you to download the latest version of their software directly from our website.  The zip file contains all of the files necessary to run ZXW Tools (trace) and Blackfish (schematics).  There is no installation process.  You just need to copy the files over to a directory on your desktop. Step 3 After you’ve copied all of the files over to a folder on  your desktop, then just run the ZXW tools executable.as shown in the picture. When your first run the software, the program will ask you if you want to activate the dong
Read more

IPhone 6P Front Camera and Distance Sensor Fault

Image
Received a iPhone 6 Plus, the customer said that the front camera can not be used, and the distance sensor has problem too. The two failures are concentrated on the front camera flex cable, which is likely to be caused by the damage of the wiring. First, we have to eliminate the possibility of the external parts fault, then consider the motherboard problem. Remove the screen assembly and replace it with a good one, we still can't turn on the front camera and use the distance sensor. Disassemble to measure the ground resistance of the front camera seat of J1111 by Fluke digital multimeter , it is found that several pins are infinitely large, and the related inductors are loose when touch with the pen. It seems that the small components are pseudo welded. 19-1- 1 Remove the motherboard and observe it under the Trinocular Stereo Microscope , we can see that the touch was repaired before. 19-1-2 The back of the sub touch chip U2402 is the front camera seat J1111, an
Read more