Repair guide MIJING ACT PRO iPhone Chip Repair Tool

How to save both of your time and effort with iPhone Baseband Eeprom IC repair? The latest MIJING ACT PRO iPhone chip repair tool is an efficient equipment that available for reading and writing datas on iPhone 4S/5G/5C/5S/6G/6S/6SP/SE/7G/7P models, repairing flash error 1.3.6.16.47.48.1669 and 3G/4G signal faults on 4S/5G/5S/5S models. Also, it can reset and repair PC BIOS. Here we will introduce its function and how to use it !

Operation Guide

• Software Download
1. Contact seller or log in MIJING official website "www.fsmijing.com"
2. find "download" - "下载中心" click into the page
3. find "Mi Jing Cloud Software"- 米景云平台“ to download and install
4. Run the software and find " drivers" - "驱动安装“ in the menu
5. Choose " CH341(码片）”drivers to install and reset your computer

• Chip Data writing and Reading Operation
1. Remove the motherboard baseband CPU you need to repair
2. Choose the " mainboard fixed chassis" for corresponding mainboard
3. Install mainboard on"mainboard fixed chassis" and fasten it by "fixed lever"
4. Run "Mi Jing Software" and click "Instrument" in menu - Chosse "Chip Repair Instrument" mode
5. Connect data cable to ACT PRO chip repair tool and computer USB port
7. Save the data file in computer after the reading is done.

(How to check the chip data is normal？It depends on whether you can read data on the left dialog box, otherwise, if there is blank, it means you get wrong operation or damaged chip" ）

Note:
For repairing flash error 1.3.6.16.47.48.1669 and 3G/4G signal faults on 4S/5G/5S/5S models, click the right side on software " 修复码片数据“ multioptions - Choose corresponding model repair options - Software will note the file you need to repair - Choose the chip file you saved in computer - Rename the repaired file and save in computer- Click "Erase Data" to erase chip data in mainboard before writing new one - Click " Open" to choose repaired file -  Click " Write" so you can write datas in mainboard chip - Remove the mainboard as soon as the writing process is done,  and connect computer flash IOS firmware to be in progress of repair operation.

8. Remove mainboard from ACT PRO chip repair tool and restall the new chip or mainboard you need to writing( Baseband CPU removing is essential)
9. Click the "Read" option, there is no need to save in computer
10. Click "Open" to choose the chip data saved in computer and click "Write"

Note:
For writing datas on iPhone 4S/5G/5C/5S models, you must erase data first, click " Erase Data" then you can wtrite data.
For other iPhone models : 6G/6P/SE/6S/6SP/7G/7P , this step can be passed.

11. Remove chip or mainboard, connect computer flash IOS firmware to test function then the whole process will be done successfullly!

That's all for the user guide today. Good luck to your cell phone maintenance!
More iPhone Baseband Eemprom programmer and operating introduction read at www.vipprogrammer.com

Comments

Post a Comment

Popular posts from this blog

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac
Read more

Setup and install the zxw tool Dongle Wizard

Image
So, you recently purchased ZXW Tools from our vipprog online store have no clue how to set it up?  Well, here is a quick guide detailing the installation process. Step 1 Unbox the ZXW tools dongle and plug it into your Windows PC.  ZXW tools does not support Mac at this time, so you’ll need a Windows compatible box. Step 2 Download the ZXW Tools software [direct link].  The ZXW tools website is in Chinese, but lucky for you, we’ve made it easy for you to download the latest version of their software directly from our website.  The zip file contains all of the files necessary to run ZXW Tools (trace) and Blackfish (schematics).  There is no installation process.  You just need to copy the files over to a directory on your desktop. Step 3 After you’ve copied all of the files over to a folder on  your desktop, then just run the ZXW tools executable.as shown in the picture. When your first run the software, the program will ask you if you want to activate the dong
Read more

IPhone 6P Front Camera and Distance Sensor Fault

Image
Received a iPhone 6 Plus, the customer said that the front camera can not be used, and the distance sensor has problem too. The two failures are concentrated on the front camera flex cable, which is likely to be caused by the damage of the wiring. First, we have to eliminate the possibility of the external parts fault, then consider the motherboard problem. Remove the screen assembly and replace it with a good one, we still can't turn on the front camera and use the distance sensor. Disassemble to measure the ground resistance of the front camera seat of J1111 by Fluke digital multimeter , it is found that several pins are infinitely large, and the related inductors are loose when touch with the pen. It seems that the small components are pseudo welded. 19-1- 1 Remove the motherboard and observe it under the Trinocular Stereo Microscope , we can see that the touch was repaired before. 19-1-2 The back of the sub touch chip U2402 is the front camera seat J1111, an
Read more