how to fix iphone battery trobble Phenomenon


More and more people use the iphone, so the iphone can be used in a variety of problems, such as the battery is not durable

how to fix iphone battery trobble?

Apple Stores will still replace your iphone battery . But that’s not an option for every consumer: some people can’t get to an Apple store; some folks need a cheaper, quicker option; and some folks (like us) just prefer to do their repairs at home

We’ve been looking for a good, consistent DIY repair solution for folks who want to replace their own iphone battery for a while. But that battery glue makes it really challenging.so that makes the replacement part more expensive for owners

We experimented with a lot of different options for how best to loosen that adhesive without compromising the battery. We tried heat—our go-to method for adhesive-logged devices. But getting heat to a iphone battery adhesive is hard: you either have to push heat through the battery (not safe), or pump enough heat through the keyboard and trackpad to turn your laptop into a hot plate (not good).

Heat exhausted, we turned to other solutions. We needed to find a solvent that was powerful enough to cut through the adhesive, gentle enough to not compromise the Li-ion battery cells, safe enough for consumers (and us!) to use, and friendly enough for the environment.

After a lot of testing and dozens of formulations, we came up with a solution. It’s a blend of household chemicals—safe to use, but potent enough to get the job done. The repair is still a fair bit of work: removing the battery requires a lot of caution and patience—but it’s definitely doable with the right tools, the right instructions, and the right adhesive removal technique.

Comments

Post a Comment

Popular posts from this blog

How to fix iPhone 6 show Power current 70mA can’t turned on

Image
Your iPhone will not turn on and you’re looking for help. It’s a problem that can be easy or difficult to fix, depending on the cause.In this article,A customer's IPhone6 after triggering it on, the turn on current is 70mA. This customer used iTunes to root it, but the root did not pass and iTunes reported error 4014. Repair Process Customer himself used air gun  to heat CPU. When connect computer to root, computer reports error 4014. In general, error 4014 suggests that CPU, Temporary Storage is more or less faulty or the power supply circuits are faulty. After removing the motherboard , we find that around the shield cover of motor drive chip U1400 there is some erosion mark, as shown in picture 5-41. Picture 5-41 Removing the shield cover , we can see that U1400 is eroded. Picture 5-42 shows erosion situation of the enlarged motor drive chip U1400. Picture 5-42 Clean the eroded places and replace U1400. Now iPhone can be turned on normally. The motor drive chip ...
Read more

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac...
Read more

What to do if iPhone 6s can't add fingerprint

Image
My iPhone's Touch ID fingerprint scanner's not working! It won't recognise the fingerprints stored in the system. How can I fix Touch ID? The iPhone 6S accidentally dropped into the water, and then it came up with a fingerprint faulty, the iPhone 6S can't add fingerprint. So the customer sent it to us to repair. Now, let's take a closer look at this iPhone and then repair it! Disassemble the iPhone by JM-P01 Toolkit  , carefully remove the iPhone motherboard. After checking, we found signs of corrosion in the fingerprint socket, and then detect MESA_TO_BOOST_EN_CONN. Use Fluke 15B+ Digital Multimeter  to measure the diode data of PP16V5_MESA_CONN fingerprint boost boot signal and 16.5V, the data is normal. Observe the iPhone PCB board carefully under the VGA Camera 7-45X Trinocular Stereo Microscope  , we found something else. The bottom pin was severely corroded after the corrosion was removed from the fingerprint boost U4040. A2 pin PP_VCC_MAIN is disconn...
Read more