No Service On iPhone 6 repair guide
when no service’ on your iPhone 6, you can not use mobile data, send text messages or make a phone call. Yes, you can connect to the internet by a Wi-Fi network. But what if there is no Wi-Fi? That’s when you got separated from the bustling world.What should I do at this time? Don't worry. The solution is as follows.
There are external and internal causes for iPhone ‘no service’ problem, which means no one-size-fits-all solution. vipprog is a professional iphone repair shopping can helo solution those problem, and hardware failure with the fix of our newly developed product.
1. Turn on the phone, searching for the signal – no service. Spread out the dialer board, enter ‘*#06#’ for IMEI code – no results. as signal failure.
2. Go to Settings – General – About, IMEI code displays right, SIM card readable, and Modem Firmware functions normally
3. Disassemble the phone, detach phone battery, take down the LCD screen assembly, then take out the motherboard.
4. Remove the shield plate on motherboard with cutting nipper(Hot air gun is not recommended here because the shield plate is hard to remove and high temperature might cause damage to components nearby). Attach motherboard to PCB holder.
5. Apply some BGA paste flux to the baseband CPU, blow it with hot air gun at 300 degrees centigrade. After a while, take down the baseband CPU.
6. Clean the tins on the bonding pad with soldering iron, then dip some rosin with Goot wick for secondary cleaning. After that, clean it again with PCB cleaner.
7. Roll out the maintenance drawing for reference. Point out the U1 Y1 pin as data signal failure. Test the U1 Y1 pin of the baseband CPU with digital multimeter, no resistance. We can conclude that the pin has been disconnected.
8. Scrape the insulation varnish off the U1 Y1 pin circuit, solder the tins on the circuit with soldering iron for cable welding afterwards. Then align a solder added copper wire with a diameter of 0.02 millimeter to the exposed circuit with soldering iron. Clean it with PCB cleaner.
9. Apply some UV curable solder mask to the aligned copper wire, then put it under the UV dryer lamp for 10 minutes.
10. Apply some rosin with soldering iron for cleaning, PCB cleaner afterwards. Once finished, reball the baseband CPU with BGA reballing stencil.
11. Apply some soldering paste with BGA scraper and smear evenly on the right place. Blow it with hot air gun for formation, take it down and blow it with hot air gun again.
12. Apply some BGA paste flux to the bonding pad, align the CPU to the right place, blow it with hot air gun at 280 degrees centigrade.
13. Once the motherboard is cooling enough, clean it with PCB cleaner. Afterwards, install the motherboard to the phone and test – IMEI code functions well.
There are external and internal causes for iPhone ‘no service’ problem, which means no one-size-fits-all solution. vipprog is a professional iphone repair shopping can helo solution those problem, and hardware failure with the fix of our newly developed product.
1. Turn on the phone, searching for the signal – no service. Spread out the dialer board, enter ‘*#06#’ for IMEI code – no results. as signal failure.
2. Go to Settings – General – About, IMEI code displays right, SIM card readable, and Modem Firmware functions normally
3. Disassemble the phone, detach phone battery, take down the LCD screen assembly, then take out the motherboard.
4. Remove the shield plate on motherboard with cutting nipper(Hot air gun is not recommended here because the shield plate is hard to remove and high temperature might cause damage to components nearby). Attach motherboard to PCB holder.
5. Apply some BGA paste flux to the baseband CPU, blow it with hot air gun at 300 degrees centigrade. After a while, take down the baseband CPU.
6. Clean the tins on the bonding pad with soldering iron, then dip some rosin with Goot wick for secondary cleaning. After that, clean it again with PCB cleaner.
7. Roll out the maintenance drawing for reference. Point out the U1 Y1 pin as data signal failure. Test the U1 Y1 pin of the baseband CPU with digital multimeter, no resistance. We can conclude that the pin has been disconnected.
8. Scrape the insulation varnish off the U1 Y1 pin circuit, solder the tins on the circuit with soldering iron for cable welding afterwards. Then align a solder added copper wire with a diameter of 0.02 millimeter to the exposed circuit with soldering iron. Clean it with PCB cleaner.
9. Apply some UV curable solder mask to the aligned copper wire, then put it under the UV dryer lamp for 10 minutes.
10. Apply some rosin with soldering iron for cleaning, PCB cleaner afterwards. Once finished, reball the baseband CPU with BGA reballing stencil.
11. Apply some soldering paste with BGA scraper and smear evenly on the right place. Blow it with hot air gun for formation, take it down and blow it with hot air gun again.
12. Apply some BGA paste flux to the bonding pad, align the CPU to the right place, blow it with hot air gun at 280 degrees centigrade.
13. Once the motherboard is cooling enough, clean it with PCB cleaner. Afterwards, install the motherboard to the phone and test – IMEI code functions well.
I m thankful to you for sharing this post.you should keep sharing such a good post.
ReplyDeleteiphone6 screen replacement services