iPhone 6 displays black screen and high-current repair guide

when you IPhone 6 displays black screen,A professional cell phone repair shop vipprog can help you.

IPhone 6 displays black screen and DC power shows the current flows normally but a little higher than that of average working iPhones.

Repair Process

Teardown iPhone and measure the diode data of each pin of display Touch screen  interfaces. The data is normal. There is no output after measuring the display power supply ±5.7v voltage. Replace the display screen power drive control chip U1505, but the same problem still shows up. Therefore, we conclude there is something wrong with the surrounding circuits’ resistor-capacitor units. After carefully measurement we find capacitor C1554 is short circuit. The location of capacitor C1554 is shown in bitmap picture 2-3 and material object is shown in picture 2-4. Replace it, the ±5.7v voltage output is normal. Assemble motherboard and turn on iPhone, the screen displays normally. Trouble is removed.

That the voltage of capacitor C1554 is under 5.7v suggests the damage of Touch screen control IC chip or low starting conditions.

Picture 2-3

Picture 2-4

Comments

Post a Comment

Popular posts from this blog

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac...
Read more

What to do if iPhone 6s can't add fingerprint

Image
My iPhone's Touch ID fingerprint scanner's not working! It won't recognise the fingerprints stored in the system. How can I fix Touch ID? The iPhone 6S accidentally dropped into the water, and then it came up with a fingerprint faulty, the iPhone 6S can't add fingerprint. So the customer sent it to us to repair. Now, let's take a closer look at this iPhone and then repair it! Disassemble the iPhone by JM-P01 Toolkit  , carefully remove the iPhone motherboard. After checking, we found signs of corrosion in the fingerprint socket, and then detect MESA_TO_BOOST_EN_CONN. Use Fluke 15B+ Digital Multimeter  to measure the diode data of PP16V5_MESA_CONN fingerprint boost boot signal and 16.5V, the data is normal. Observe the iPhone PCB board carefully under the VGA Camera 7-45X Trinocular Stereo Microscope  , we found something else. The bottom pin was severely corroded after the corrosion was removed from the fingerprint boost U4040. A2 pin PP_VCC_MAIN is disconn...
Read more

Setup and install the zxw tool Dongle Wizard

Image
So, you recently purchased ZXW Tools from our vipprog online store have no clue how to set it up?  Well, here is a quick guide detailing the installation process. Step 1 Unbox the ZXW tools dongle and plug it into your Windows PC.  ZXW tools does not support Mac at this time, so you’ll need a Windows compatible box. Step 2 Download the ZXW Tools software [direct link].  The ZXW tools website is in Chinese, but lucky for you, we’ve made it easy for you to download the latest version of their software directly from our website.  The zip file contains all of the files necessary to run ZXW Tools (trace) and Blackfish (schematics).  There is no installation process.  You just need to copy the files over to a directory on your desktop. Step 3 After you’ve copied all of the files over to a folder on  your desktop, then just run the ZXW tools executable.as shown in the picture. When your first run the software, the program will ask yo...
Read more