How to repair iPad Air displays white Apple logo

When your ipad fails, you don't need to be nervous and worried, there's a professional solution

All kinds of iphone ipad repair tool can be found in vipprogrammer.

Our product inclode iphone ipad repair parts, repair tools and other accessories. All parts are put to the test in QC department. We exactly know how important of quality for every enterprise.

Our price is much competitive when compared in the whole market.

Lead Time
3-4 days via DHL
 
The iPad shows white Apple logo after power on and then shows black screen, later white Apple logo again. It reboots repeatedly, as shown in picture 2-26.

Picture 2-26

Repair Process

After teardown, remove shielding case and press the power button. When iPad shows white Apple logo, use hand to touch each main chip and feel power chip U8100 hot. The location of U8100 is shown in picture 2-27. Without connecting display screen, press power button. Touch U8100 and now it is not hot.

Picture 2-27

Analyze according to display circuit working principle. Without display screen , the backlight bootstrap circuit of display screen does not work. With display screen, the circuit will work. Thus, the problem happens on the display screen backlight bootstrap circuit.

Continue to analyze the backlight bootstrap circuit (picture 2-28 and 2-29). IPad Air’s backlight bootstrap circuit has two voltages, PPLED_OUT_A and PPLED_OUT_B.

Picture 2-28

Picture 2-29

After measuring, the voltage drop of D8228 on motherboard is 1.9v, which is close to the state of an open circuit. While the normal voltage drop should be about 0.2v. The relevant circuit of D8228 is shown in picture 2-30. Measure the negative pole voltage of D8228 is 0.5v when getting electricity on but do not press the power button. But the normal data should be battery power supply voltage (3.7-4.2v).

Picture 2-30

Based on the data gained above, we know D8228 is damaged. The location of D8228 is shown in picture 2-31. After replacing it and measuring, the voltage of negative pole rises to 16.7v and the chip is not hot. But when enter system, iPad
Air still reboots. First root it to exclude the problems from software.
Picture 2-31

Under the stare of power off, press HOME button and then insert USB cable to enter recovery mode to root, as shown in picture 2-32.

Picture 2-32

After using iTunes to install the newest firmware, machine enters system normally, as shown in picture 2-33. Trouble is removed.

Picture 2-33

There are hundreds of ipad repair
tools(http://www.vipprogrammer.com/phone-repair-tool-manufacturers-87)
in the market. But what you should do is to get only those which you need, above is an absolutely indispensable kit for anyone who wants to repair smart phones, ipads and tablets. Lastly, may you have a pleasant experience in your ipad repairing!

Comments

Post a Comment

Popular posts from this blog

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac...
Read more

What to do if iPhone 6s can't add fingerprint

Image
My iPhone's Touch ID fingerprint scanner's not working! It won't recognise the fingerprints stored in the system. How can I fix Touch ID? The iPhone 6S accidentally dropped into the water, and then it came up with a fingerprint faulty, the iPhone 6S can't add fingerprint. So the customer sent it to us to repair. Now, let's take a closer look at this iPhone and then repair it! Disassemble the iPhone by JM-P01 Toolkit  , carefully remove the iPhone motherboard. After checking, we found signs of corrosion in the fingerprint socket, and then detect MESA_TO_BOOST_EN_CONN. Use Fluke 15B+ Digital Multimeter  to measure the diode data of PP16V5_MESA_CONN fingerprint boost boot signal and 16.5V, the data is normal. Observe the iPhone PCB board carefully under the VGA Camera 7-45X Trinocular Stereo Microscope  , we found something else. The bottom pin was severely corroded after the corrosion was removed from the fingerprint boost U4040. A2 pin PP_VCC_MAIN is disconn...
Read more

Setup and install the zxw tool Dongle Wizard

Image
So, you recently purchased ZXW Tools from our vipprog online store have no clue how to set it up?  Well, here is a quick guide detailing the installation process. Step 1 Unbox the ZXW tools dongle and plug it into your Windows PC.  ZXW tools does not support Mac at this time, so you’ll need a Windows compatible box. Step 2 Download the ZXW Tools software [direct link].  The ZXW tools website is in Chinese, but lucky for you, we’ve made it easy for you to download the latest version of their software directly from our website.  The zip file contains all of the files necessary to run ZXW Tools (trace) and Blackfish (schematics).  There is no installation process.  You just need to copy the files over to a directory on your desktop. Step 3 After you’ve copied all of the files over to a folder on  your desktop, then just run the ZXW tools executable.as shown in the picture. When your first run the software, the program will ask yo...
Read more