How to fix No Service on iphone 6 but SIM Card working normally


If you IPhone 6S has no service with SIM card.

Repair Process

There are IMEI, modem firmware and ICCID in “about iPhone”, but there is not IMEI when dialing *#06#. Checking PCB circuit diagram bitmap we find the testing point of RFFE1 bus is PP3170_RF and PP3171_RF. The testing point is shown in picture 1-51 and the material object is shown in picture 1-52.

Picture 1-51

Picture 1-52

After measuring the diode data of RFFE1 bus, we find the data of PP3171_RF is too large. Teardown baseband CPU to measure the diode data of pin U1 and the data is infinite. Scratch a circuit near pin U1 and connect it to pin U1 with a jump wire, as shown in picture 1-53. After placing the wire, measure the diode data of U1. The data is normal.

Picture 1-53

Doing BGA Reballing on baseband CPU (in picture 1-54), and weld baseband CPU to PCB board.

Picture 1-54


Power on and use an Multimeter oscilloscope to measure the wave of RFFE1_DATA of PP3171_RF under the state of bare board. The wave is normal as shown in picture 1-55.

Picture 1-55

Measure the wave of RFFE1_CLK of PP3170_RF. The wave is normal as shown in picture 1-56.

Picture 1-56

Assemble the board to assembly and enter system to test. Everything is normal. The trouble is removed.

Comments

Post a Comment

Popular posts from this blog

Slove iPhone X Won't Turn On

Image
Customer delivered a iPhone X and described the fault is not to boot after the phone drop accidentally. It reports error 56 when restore the iPhone X. How to repair this fault? Because iPhone X is the two board connected through the middle column, it is easy to drop the point. It may be that the solder points from NFC chip to the CPU part have fell off. Take apart the iPhone X by iPhone Screwdriver Repair Tools , take the upper board off the main board, when separate the main board we see a row of points have fell off. Picture 19-3-1 Look at the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Picture 19-3-2 Then the tin of the middle column is repaired by iPhone X BGA reballing stencil , and the AP part is welded bac
Read more

Setup and install the zxw tool Dongle Wizard

Image
So, you recently purchased ZXW Tools from our vipprog online store have no clue how to set it up?  Well, here is a quick guide detailing the installation process. Step 1 Unbox the ZXW tools dongle and plug it into your Windows PC.  ZXW tools does not support Mac at this time, so you’ll need a Windows compatible box. Step 2 Download the ZXW Tools software [direct link].  The ZXW tools website is in Chinese, but lucky for you, we’ve made it easy for you to download the latest version of their software directly from our website.  The zip file contains all of the files necessary to run ZXW Tools (trace) and Blackfish (schematics).  There is no installation process.  You just need to copy the files over to a directory on your desktop. Step 3 After you’ve copied all of the files over to a folder on  your desktop, then just run the ZXW tools executable.as shown in the picture. When your first run the software, the program will ask you if you want to activate the dong
Read more

IPhone 6P Front Camera and Distance Sensor Fault

Image
Received a iPhone 6 Plus, the customer said that the front camera can not be used, and the distance sensor has problem too. The two failures are concentrated on the front camera flex cable, which is likely to be caused by the damage of the wiring. First, we have to eliminate the possibility of the external parts fault, then consider the motherboard problem. Remove the screen assembly and replace it with a good one, we still can't turn on the front camera and use the distance sensor. Disassemble to measure the ground resistance of the front camera seat of J1111 by Fluke digital multimeter , it is found that several pins are infinitely large, and the related inductors are loose when touch with the pen. It seems that the small components are pseudo welded. 19-1- 1 Remove the motherboard and observe it under the Trinocular Stereo Microscope , we can see that the touch was repaired before. 19-1-2 The back of the sub touch chip U2402 is the front camera seat J1111, an
Read more